Beiträge von Olaf Krause
-
-
-
Check you minimum SOC settings and capacity using the SOC discharging & voltage curve as well. If it immediately drops to a low soc a "virtual" cell has reached low Volatage and BMS reacts on it.
For SI setting see RE: Nächstes Projekt: Batteriespeicher für daheim
-
-
-
-
Reagarding the Parameter for the SI I am completely lost now - I don't see any of those on my SI. I can also only compare with the sunnyportal. Sunny Explorer does not give me any annswer on config settings (need to figure out why).
@ALL: someone able to suport here?
Charging control should be at BMS - Maybe I am wrong but somewhere you can set the SI to LION so BMS is external via CAN. If the SOC displayed in SunnyPOrtal is correct your setting should be OK otherwise you would get no values.
Regarding the resistence I did not get your question.
-
RE: Nächstes Projekt: Batteriespeicher für daheim
is a post how the SI was connected by a user.
Asymmetric between phases? You have only one phase or? Here my current AC readout - unfortunately my SI does not answer on settings request
-
thick copper?
RE: Nächstes Projekt: Batteriespeicher für daheim
Could be wrong measurement or bad connection - I would monitor if always the same cells are showing the higher resistance.
All cells will reach the 4.1 - it is more about that the ones with less capacity - the BMS will have to compensate with balancing acitivity, as they otherwise would be "overcharged" - if your BMS get's hot even if cooled it looks like a lot balancing. Acceptable for the first few cycles but also to be monitored.
-
-
-
-
-
-
The SI gets all signals from the BMS (via CAN) and the SMA Homemanager/Sensor (via LAN) measuring if you feeding into the grid or consuming. So no need to connect extra current sensors etc. to the SI.
Could provide my SunnyExplorer setting this evening (if I do not forget)
Some settings that I posted before:
-
I only did a full charge (let the BMS balance) discharge, fullcharge cycle to calibrate at the beginning. Since this year I lowered the balancing start voltage as it seems some cells are no longer that optimum. I need to check them individually and maybe replace some - but nmot checked yet. No problem in summer when regularly reaching 100% but winter time is a but of calibration.
-
-
Mich ewig nicht mehr mit den Softwareständen des i3 befasst - es lief einfach ohne Probleme.
Letzte Woche war dann doch ein Update fällig weil die Toleranzen der Feststellbremse mit der alten Version von 2016 dazu geführt haben, dass sie ab und zu nicht mehr anziehen wollte (Fehlermeldung). Die neue Version soll wohl größere Toleranzen akzeptieren. Kosten 70€ Bremsentest und 130€ die SW aktualisierung (Ca. Angaben).
So auf die schnelle keine Infos zu den ganzen Zwischenversionen gefunden - wenn jemand einen Link hat ... komplettiere ich die Tabelle mal.
-
Schau Dir mal https://enbw-eg.de/netcontrol/wp-…meldedialog.pdf an (ich hatte die nummer nicht). Evtl. hilft das weiter - ich hatte Glück und kannte die Bearbeiter beim Netzbetrieber schon von meinen PV Anlagen und konnte direkt pesönlich alles regeln. Im Notfall musst Du wohl einen Elektriker damit beauftragen.
-
Irgendwo sicherlich in den tiefen meiner Datenablage. Habe erstmal nur ein Formular gefunden:
Inhalt ist nat. entsprechend anzupassen - war alles machbar.
Dazu gab es noch das Datenblatt Messkonzepte:
Dann noch die aktuellen Datenblätter der Wechselrichter (meine passen sicherlich nicht zu Deinen). Das Zeuch hatte ich der Syna geschickt und gebeten mir doch schicken was nmoch fehlt - dann ping pong.... irgendwann war gut. Kommt sicherlich auch drauf an was für einen bearbeiter du erwischt.
-